Pages

Thursday, November 24, 2022

Tighten a loose freewheel on the trail

 I have had bicycle freewheels come loose while riding, many times and on multiple bikes.  Here is a video showing it.



You start to hear and feel a knock, worse in some gears that others.  As it progresses, it may struggle when changing gears.  If you let is continue, it will come apart and leave your stranded.  



Maybe I am the only one that seems to have this problem but I doubt it.  The first time this happened I was out in the desert up a long hill.  I felt it happening but did not stop to check into it.  It finally got so bad the freewheel came apart and locked so there was no ratchet action anymore and the pedals just followed the wheel.  It made for a long trip home.  My bike was under warranty so I got a whole new rear wheel assembly.  The new one did the same thing.  This time I caught it early.  Normally you need to take the wheel off and use a special spanner for this.  I only had some basic tools I carry on the bike.  I finally used a Philips screwdriver and some ingenuity to tighten it back up without taking anything apart.    

Here is a photo showing the freewheel off the bike so you can see how to place the screwdriver.





There are small holes for the spanner. Push the Philips screwdriver into that hole at a bit of an angle. Since the bike will be assembled on the trail, there are only a few areas where you can even see this part of the freewheel.  Generally in the slot where the axle bolts to the frame.  While pushing in hard on the screwdriver, rotate the wheel in the forward travel direction.  This will cause the whole freewheel to move with the wheel but since you are holding the freewheel nut with the screwdriver it will stop against the frame and tighten the nut.  Since you have the leverage of the whole wheel diameter, the weak point of this is keeping that screwdriver held tight into the nut hole.  You can help this by holding the screwdriver at a bit of angle.  Hard to explain in words but it works well.  

The freewheel bearing preload is set with shims, not a specific torque, so you really can't overtighten it, especially since the screwdriver approach does not give enough grip to overtighten it.  













Saturday, November 5, 2022

SEMA 2022

 


Like last year, I attended SEMA 2022 for the Friday Experience.  This is a great opportunity open to the public.  Also like last year, I wanted to see what the industry is embracing going forward with the rapid change to electrification going on at the OEMs.  

When I entered the Las Vegas Convention Center, the line was very long.  It was at a different place than last year making the comparison a bit harder but it sure seemed like more people this year.  

This years SEMA Electrified was much larger than last years. In addition, there were manufacturers of EV components and kits all over the show.  Below are some photos of several EV systems and components I found at the show.






















A Porsche 911 specific kit.





There were many other EV conversion suppliers here.  There were also many EV conversions on display around the show.

Absent was any hybrid conversion parts or kits.  A person could of course use many of the components such and controllers, batteries, chargers, etc., in a hybrid system but what is missing and needed are hybrid motors.  In my opinion this is a gap.  Of course there are many people interested in full-EV conversion which is a niche market itself but there is another niche for hybrids that is mostly unserved.  From what I can tell, Vonnen has this market to itself at the moment.  The Vonnen system is not available as a kit and it is priced very high, well out of reach of most.  

As I wrote years ago, I believe there is room for aftermarket performance hybridization kits.  SEMA would be the place to find this and I saw nothing.  However, the expansion of EV components and kits are paving the way for hybrids as well.  

Obviously SEMA is a huge show with tons of other performance systems, tools, shop equipment, and other suppliers that offer components and services to shops.  There is also a huge display of all kinds of exotics contraptions that take up the whole convention center parking lot.
This is not just a photo angle thing.  The bumper was actually the height of my head standing straight up.




I saw several similar to this.  A mini monster truck.  This one had a supercharged GM LS V8 in it, as I think most did.  



Notice the smoke coming from the top right in the photo above.  That was a drift area where they were shredding tires all day long.  

New Ford Broncos were very popular at the show.  Many selling components and kits and others doing major modifications like this one above.