Monday, November 20, 2017

Porsche 987/997 door panel removal


Removing the door panel on cars can be tricky and you often break things.  The are generally attached with an assortment of hidden screws and plastic clips.  I recently removed the drivers door panel on my 2006 Cayman S so I thought I would share some handy info for the next person.

Here are the tools you will need.

  • Torx T30 bit and the proper driver or a long T30
  • Flat blade screwdriver
  • Putty knife

I also had a T30 set which I used for convenience.

Start by removing the trim at the top rear of the door panel and the screw under it.


Then remove the top front panel and the screw under it.  Be careful with this panel.  Pry the bottom edge out and then lift up to remove.  This panel hooks at the top so do not pry on the top.


Now remove the leather trim cover over the door pull handle.  Do this by opening the compartment and prying out on the leather covered trim.

It looks like this with the trim removed.
Now remove the screws at the front and back that are set deeply into the panel.


Now remove the round plastic cover and the screw behind it, both being behind the door latch handle.  You need to hold the handle all the way out to do this.

 This one is best accessed with a shorter torx to ensure you are squarely aligned and don't strip the torx screw or bit.  The tool shown above is not ideal actually.

Next you need to carefully pry the bottom edge of the door panel out releasing the clips.  Here is a photo of the inside of the door panel showing where the plastic clips are.

Unfortunately it seems there is no great way to do this.  Often one or 2 of the clips will not properly release and the panel area holding the clip will break instead.  Plan ahead with some good epoxy to fix the damage.

Once you have the panel disconnected from the door, you need to disconnect the electrical connectors and the door latch cable.



 The door handle cable clips in place with that white plastic cable end.  Start by prying the ends outward away from each other.  Then slide the clip forward until it disengages with the slot.  Once the white plastic cable end is apart from the panel, rotate the cable assembly perpendicular with the hole to disengage the cable.
Be careful with the door latch cable as it does not have much room to work with and you can easily break it.  Depending on options, you may not have all the same connections.

Here is what the inside of the door looks like.




The clips hare 2 piece where the center expands the outer piece when the door panel is pushed in place.  When you pull the door panel, the center is supposed to pull out releasing the clip.  See these 2 clips in the photo below.
Notice the clip on the left is released and the one on the right is still expanded.  They are supposed to release like the one on the left.  If this happens, remove the clip and release it by pressing the center back out.  I used a vice and a hammer for this.

Make sure all 4 tips tuck under the tip properly.  If one is sticking out, push the center in far enough to tuck it back in the then press the center back out fully.

Sunday, November 12, 2017

Testing a cars charging system with only simple tools

There are many things that can cause a car to not start.  First, lets clarify the difference between not cranking and not starting.

Cranking is when the starter spins the engine.  This is done by the starter motor engaging the engine and turning the crankshaft.  Back in the very old days this was actually done by a person with a crank handle directly cranking the engine over by hand, hence the term "cranking".  For the last 100 years, this is done by a starter motor.

Starting is a more general term to mean the engine has not reached a running state.  Starting includes first cranking and then the engine generating combustion to run on its own without the starter.  This requires fuel, spark, cranking, and a bunch of mechanical bits working in harmony.

The rest of this discussion is just about cranking.  The 2 most common components at the root cause of failing to crank are the battery and the starter.
Figure 5-1: Electrical System
Figure 5-2: Starting System

Here is a good article introducing some of these basic components: http://www.military.com/off-duty/autos/auto-repair-electrical-system-tips.html

There are interlocks and security systems that may prevent the vehicle from attempting to crank.  If this happens your car won't even try, meaning that to turn the key to the crank (start) position and year hear nothing happen.  A completely dead battery can also cause this but of course you would have already noticed that no electrical systems are working at all.  You have to use the key to unlock the car as the remote won't work.  There will be no dome light or dash warning lights.  Nothing.  If this is the case, start by charging the battery with a charger, or jump starting.

If the car does have battery power, then next question is does it have enough.  If you are able to unlock with the remote, and you see the done light and other lights in the car, then your battery is not completely dead.  However, it still may not be bale to crank.  Often this will cause the engine to crank slowly or you may just hear clicking near the engine.  If turning the key to crank results in nothing, and the dome light and other lights don't even dim, then something is preventing the car from attempting to crank.  This may be the security system or interlocks such as neutral trans gear or clutch pedal not depressed.

Another common cause of cranking problems is corroded battery terminals.  The battery has acid in it but this acid can seep out or come out as vapor and corrode the terminals.  Here is a photo of badly corroded terminals.
Image result for corroded battery terminals
This will break the connection so the battery power cannot be used by the car.  This can be cleaned using baking soda and water.  Remove the terminals and clean the connection between the battery post and terminal with a wire brush.  You can by a terminal cleaner at any parts store. Here is a typical example of a battery terminal cleaner.
Image result for corroded battery terminals cleaner
Be careful as the terminals may look OK on the outside bey be corroded between the battery post and terminal where it matters.  Sometimes you can hear crackling or bits of smoke while trying to crank if the corrosion is there.  Sometimes you can loosen and twist the terminal on the battery a bit and get it to work for a while.  

If all that passes and the engine does indeed attempt to crank it needs to crank the engine fast enough to start.  A weak battery will generally show up with the symptom of slow cranking or not being able to completely crank.  This is somewhat hard to describe.  The sound of the engine cranking is different, slower.  It may sometimes appear to stop cranking for short periods and then resume slowly.  Eventually is will stop cranking and often make clicking noises.  The battery has a finite life.  It will die eventually.  Eventually can be in as little as 3 years, or sooner if it experiences a premature failure, which does happen.  It is the most likely cause of not cranking, if the electrical system is allowing the attempt to crank.  Generally this problem will start out small and get worse over time.  You may notice a bit slower crank that continues to get a bit worse over the course of a week or two.  Some battery failures are much more instant where it goes from working OK to not even being able to crank on the next crank attempt.

If the alternator is not charging this will also deplete the battery and give similar symptoms to a weak battery.  There are some quick checks you can make to see if your alternator is working.  First of all there is a charging indicator in the car.  Almost all cars have a light or a message on the display if the alternator is not working. This light will be ON normally with the key ON and the engine not running.  However, if it stays ON while the engine is running there is a charging system problem.
 

There are other failure modes that may cause no charging yet this light does not come ON.  Here are some quick checks you can do to confirm the charging system is working.

https://photos.app.goo.gl/uwHjBGnB4NI1j76r1

The alternator is belt driven from the engine crankshaft.  If it is not charging, make sure the belt is turing the alternator.  Some cars also have a large fuse between the alternator and the battery.  Make sure that fuse is in place and not blown.

If your battery is OK and your alternator is working but you still have slow cranking or it fails to crank, you may have something in the electrical system that is drawing too much power when  the car is not running.  Check for things like dome light or glove box lights being left ON.  Modern cars have many complex electrical system that do draw some power even when the engine is not running.  This makes finding an inappropriate draw more difficult and vehicle specific.  Some things to look for is relays sticking ON.  This issue can often cause an intermittent draw which is even harder to find.  One of the more likely relays to stick is the fuel pump relay.  If you shut the car OFF and exit the vehicle but hear a humming noise from under the car, your fuel pump relay may be stuck ON.  These relays are often about ice cube sized blocks in one of the fuse boxes.







Sunday, October 1, 2017

Porsche Cayman S Brakes

I do track days in my 2006 Porsche Cayman S.  The car is basically stock.  This article is a collection of my thoughts around the topic of brakes.

Pads

When I got the car it had a little over 60k miles on it.  I replaced the brake pads with Hawk HPS.  They seemed OK but not really an improvement over stock.  At Putnam Park and Autobahn I did notice these pads would start to fade when hot so I switched to Hawk Street/Race pads which made a huge difference.  These Street/Race pads are basically race pads that work down to cold temperatures.  They are noisy and create copious amounts of dust like any other race pad so its not something you actually want to drive around with daily but they do work for the street, unlike race only pads.  The nice thing about these is you can swap them in at home and drive to/from the track with them and be safe.  The noise when stopping at times is only somewhat embarrassing but not enough to be worth the hassle of swapping pads at the track.  The stopping power is more than double the stock or HPS pads.  They create far more friction for the same pedal pressure.  So much that it takes some getting used to as the first few times you hit the brakes after swapping them in you are surprised by how hard it stops with such little effort.  Once you get used to driving with them, swapping back to the street pads feels a bit alarming at first.

Tire Rack produced this chart showing the various Hawk brake pads:
Hawk Brake Pad Comparison - Tire Rack

MU is the coefficient of friction, higher means more friction.  More friction means more braking force for a given pedal pressure.  Notice that most race pads do not work well at low temperatures which makes them a problem for street use.  In this case low temperature is often well above ambient.  As you can see some of the pads perform very poorly below 300F.  In addition to the problems at low temperatures, they are generally very noisy and can produce copious amounts of dust too.

Rotors

Most Porsches come from the factory with drilled rotors.  The reason drilled rotors became popular is performance applications decades ago was because of a gas layer that would form at high temperatures cause interference between the pad and rotor.  Modern performance brake pads have significantly reduced this problem, and better solutions have evolved.  One of the problems with drilled rotors is they can crack under the temperatures and stress of track use.  Mine started cracking at Road America which is particularly hard on brakes.  Here is a photo showing the small cracks starting to form.
This rotor is not too bad but those cracks can grow.  In extreme cases, the rotor can break off in chunks which is dangerous.  The best solution for track duty is slotted rotors.  I switched my rotors to Sebro slotted.  This photo shows the slotted version next to the factory rotors.

The slots in the rotors help clear the gas layer but don't tend to crack like the drilled rotors.  The slotted rotors also have more metal mass to absorb more heat.  This will help slow down the heating some under hard braking.  The heat can then be released between corners when the brakes are released.

Cooling

Brakes slow the car down by converting mechanical energy (momentum) into heat.  Changing the momentum of the car requires power (HP).  The engine provides the power to accelerate and the brakes provide the power to decelerate (in conventional powertrains).  Normally the braking power capability is much higher than the engine power.  This is a large amount of energy that the brakes much dump as heat.  The rotors require airflow to facilitate this cooling.  The Cayman/Boxster and 911 sports cars have brake cooling ducts to guide more air to the rotors.  The Porsche GT (GT2, GT3, and GT4) cars have more effective cooling ducts that can be fitted to the other 911 and Cayman/Boxster models.  I installed GT3 cooling ducts on my Cayman S.

Here is a photo of the factory cooling duct.
Here is a comparison of factory versus GT3 cooling ducts.
 Here is the GT3 cooling duct installed.

Brake Hoses

The brake hydraulic system has very high pressures.  Most of the system uses steel allow lines to route the fluid between the brake components.  However, the brake calipers must move relative to the chassis so hoses are required for this part.  Those hoses are generally made of reinforced rubber.  The problem is that even though these hoses are reinforced to reduce expansion, they still do exhibit some expansion under high pressures.  The fix for this is stainless steel hoses.  There are several available in the aftermarket but make sure you use DOT and TUV approved hoses.  

Brake Fluid

Brake fluid is NOT created equal!  Also, good quality fluid with high wet and dry boiling points is very important, especially in a car that will be used on the track.  When driving at speed on the road course, the car will see repeated heavy braking for 25 minutes or more at a time.  This will cause the calipers to heat up.  If the temperature gets high enough, the fluid can boil.  When this happens the boiling displaces fluid in the caliper with gas.  The displaced fluid is pushed back into the master cylinder.  The gas is compressible.  The next time you hit the brakes the pedal goes to the floor with little to no braking at all.  This is a very dangerous situation and must be avoided.  Any decent track inspection checklist will include replacing the brake fluid just before the event, generally within 30 days.  This is a simple procedure and even expensive brake fluid is far cheaper than loosing brakes at the track.  A good DOT 4 brake fluid is Motul 600 or 660 which is available from many parts stores that sell performance products.  There are other high performance brake fluids.  Pay attention to the wet and dry boiling points.  The reason it needs to be changed so often is water will mix with brake fluid, unlike oils.  Humidity and condensation will get into the brake fluid over time.  Vehicles that do not see high brake temperatures are far less likely to have a problem.     

Tuesday, July 4, 2017

What good is a Smartwatch?

I waited a long time to even try out a smartwatch.  I don't like wearing watches in the first place, and the phone in my pocket has all the info I need.  I didn't see the use for a smartwatch.  I do however, like tracking my fitness especially with bicycling.  I had a Polar Bluetooth heart rate sensor that I used but it quit working.  I also did not like wearing it.  I wanted a better heart rate sensor so I decided to look into smartwatches.

I chose the Motorola Moto 360 Sport.  These have been around for a while and you can often find them on sale for a great price.  I think I paid $169 for mine but I have seen them under $100 sometimes.  It has the optical heart rate sensor.  It came with Android Wear 1.5 but it should be upgraded to Wear 2.0 any day.

Uses

While I was certainly a naysayer on smartwatches, I have found more uses for mine than I thought.  I wear it every day now.  I don't think I would spend over $200 to get one but for the price I paid, I feel I am getting the value from it.

Fitness Tracking

May first use for the watch was for heart-rate monitoring during bike rides and walks.  I wanted a device that would integrate with the apps I use for tracking these activities.  I use Google Fit for my daily activity tracking.  I was using Cardio Trainer for bicycling.  I had also used My Tracks for this in the past.  It turns out that Cardio Trainer and My Tracks do not support the heart rate from this device.  Lame!  So, I switch to a more popular biking app called Strava.  This is a better app than Cardio Trainer anyway and it gives nice graphs for heart rate, as well as the rest of the data.  It also integrates with Google Fit.  Very nice.

Notifications

Sometimes it would be handy to see notifications without pulling the phone from my pocket.  I know this is a first world problem but what the heck.  Some of the more useful things are:
  • Rejecting callers.  Spam calling is totally out of control and it is very handy when one of these calls comes in to just glance at the caller info on the watch, and swipe it away.  
  • Navigation.  I didn't expect this one.  I am all about stopping distracted drivers.  People need to hang up and drive.  You should not take your eyes off the road.  I was using Google Maps to navigate on a trip.  The phone was on the seat, not visible while driving.  I was on a long straight stretch of interstate and wondered how far it was to my next turn.  I glanced at my watch and there it was.  Just a small message with the distance to, and direction of the next turn.  Nice.  
  • Seeing the time and date.  It is a watch after all.  There are many useful watch faces that are informative.  It shows the time and basic info even when the screen is off.
  • Seeing general notifications.

Development

As an amateur Android developer I wanted a device that I could write apps for if I wanted to.  Learning Android Wear development should be easier since I am familiar with Android. The first app I started for Android Wear is a remote control for my Gamin Virb Ultra 30 action camera.  I just wanted to be able to start/stop recording and maybe snap a photo using the watch as the remote.  I did get the remote working on the phone first so I could learn how to interact with the Garmin.  Once I did that, I created a wear app for the watch.  Getting the basics going was not hard.  I don't have this app done yet though.  There is a feature I depended on that Wear 1.5 does not support.  The alternative was to use the watch app in conjunction with its phone counterpart to control the camera.  That is a work in progress.

Smartphone Shopping Summer 2017 Edition

Overview

I have not posted about smartphone shopping for a while so I thought I would capture my thoughts here as some friends have been in the market.  As you know, I prefer Android devices for many reasons:
  • Open source software
  • Large Play Store full of great apps
  • Compared to other operating systems, Android allows more flexibility.
  • Google is not evil.  There are many free features and services that are best in class
  • App to app integration.  Sharing for instance.  You can share from any app to any app you want.  Nobody is forcing you down what they want.
  • Many excellent devices to choose from.  This competition is great for both price and features.
  • Micro-USB or USB-C standards.  You can buy cables, chargers, etc from whoever you want as competitive prices.
  • SD card support.  You are not stuck with the space the device is made with.  Some support Micro-SD cards up to 2TB.  
  • Access to see files, folders, data, photos, etc.  You can also simply connect to a PC and browse it like a USB memory stick.  

Brands, Skins, Preinstalled Apps

I lean heavily towards Motorola devices.  I think they offer the best value.  Other devices have higher end specs but they come with a bunch of unwanted skins and bloatware.  For instance, Samsung, LG, and HTC all have very heavy skinned versions of Android.  It is so heavy I have a hard time finding things.  Samsung also makes their own versions of basic apps that replace the Google versions.  This is just a mess in my opinion.  These are also installed in the system meaning you can't really remove them without rooting.  All of this just hogs up more device resources so that faster process and more RAM are needed because of all this bloatware.  I don't understand why these device makers continue to do this when article after article complain about it, it costs them to make and maintain it, and many users don't even want it.  Motorola has the closest to stock Android as you can get short of a Nexus or Pixel.  

It is very interesting that devices are marketed to the public showing pre-installed apps as a feature worth paying for.  To me that is like marketing a sedan with pre-installed junk welded into the trunk that you don't want and can't remove.  Now you have a less usable car.  You can't choose what is in the trunk.  Definitely get the device with the least pre-installed stuff as you can get.  Installing apps is very simple and there are many great free apps on the Play Store.  

While I have had Motorola devices almost exclusively, I have had a Lenovo tablet.  I like the hardware but the OS is terrible.  Lenovo has a bunch of bloatware in this device.  The Lenovo launcher was the worst I have ever used.  It had apps permanently in the home screen.   They wanted to force you to use their awful apps, and those they were paid to pre-install.  I was able to fix the home screen with Google Now launcher and disable all the bloatware.  I was able to even uninstall some of it.  

My Choices

So, which device would I buy if I were shopping right now?  Here are some features that I prioritize:
  • Qualcomm Quick Charge.  This is a game changer.  Many devices has other fast charging technologies but they don't really compete.  Quick Charge uses a proprietary technique to boost the voltage so that standard cables work.  You can only boost the current so far before the loss in the cable becomes a real problem.  Most chargers only support 5V charging.  Quick Charge goes up to 12V.  You can put almost 3 times the power through the same cable.  I have Quick Charge 2.0 on my 2015 Moto-X and this is a must have feature for me.
  • A big battery.  A smartphone with a dead battery is useless.  This obsession with thin is ridiculous.  Honestly, today's phones are often too thin.  I would like to have a 6,000mAh or bigger battery if I could and I would gladly put up with the extra 6mm.  
  • At least 4GB of ram.  This is important so the device does not lag when running large apps or switching between them.  Today we also have many background processes and the device needs this ram to manage it efficiently.
  • A fast 64bit multi-core CPU running at over 2GHz.  I would say a quad minimum but 6 or 8 even better.  .  
  • It must be unlocked and free of carrier software.  
  • A good camera.  These are getting better all the time so there are many good choices here.  I don't need to record at 4k but HD is needed.  I want tomething that is fast.  I want to be able to capture moments as they happen so it must open, focus, and snap very fast.
  • A decent sized screen.  I like something in the 5.5" range as my vision is not so great anymore.  I don't need over HD though.  Even 720HD would be fine for me.  The higher resolution you get, the more processing power it eats up, which also eats more battery.  
  • Must work on Verizon.  I have a love/hate relationship with Verizon.  They have clearly become evil but they simply have the best network.  I still have the old unlimited plan.  Around town I often get over 50Mb speeds.  It is rare that I don't have service even on trips.  
  • Regardless of an SD slot, the device needs at least 32GB of memory.  This is so you can install all apps and app data on the device.
  • An SD card slot.  While you want all your apps on the device, the SD card opens up tons of space for media.  This is especially important if you shoot much video.  Strore your media, photos, and video on the SD card and save the on-board memory for apps.  Ideally the device would support the full SDXC standard which means you can use cards up to 2TB (even though that size is not yet available).  Several phones do support this.  
  • NFC.  I have starting using mobile pay.  I tried Android Pay but my cards stopped supporting it.  Now I use Capital One Wallet and it generally works well.  Honestly it is still faster and easier to just use the card in most cases but I am really hoping someday we won't need a physical wallet and this is the start of that.  I just want this option.  
  • Fingerprint sensor.  While this is low on my list, and is not a must have, it is handy at times.  
  • A good old fashioned headphone jack.  This is low on my priority list but it is something to consider these days.  I tend to prefer Bluetooth anyway so I don't need this very often.  
Here are the ones at the top of my list.

Moto G5 Plus 4GB/64GB

I would get the one with 4GB Ram which is only available with 64GB memory.  This device retails for $299 which makes it a bargain.  It has 4GB ram which gives apps plenty of space without having to swap in and out.  That makes the device more responsive, especially when switching between apps.  The 64GB memory is also nice as you want all your apps and their data on the device memory versus and SD card for speed.  SD cards are great for media and data, and this device has the slot.  It is unlocked so there is no carrier bloatware and this should also make updates faster.  It has Quick Charge 3.0 for fast battery charging.  It does lack NFC for mobile pay and certain other features, if you use that.  It has a Snapdragon 625 chip set clocked at 2.0GHz so it should keep up with most apps, except maybe some of the games that need top end performance.  For the vast majority of users, this device should be a great fit.

Moto G5S Plus

Coming soon.  This is an upgrade to the Moto G5 Plus.

Moto Z2 Play

The Moto Z line is Motorola's flagship devices.  The real unique thing about them is the Moto Mods. Moto Mods are magnetically attached devices that cover the back of the phone.  Some of the most appealing for me are the batteries.   While the Moto Z devices are silly thin in my opinion, once you attach a Moto Mods battery, it is about right.  This is even better than the removable batteries of yesteryear since you can swap the Moto Mod when the device is ON.  Just pop one off and attach the other.  Some of the Moto Mod batteries also have quick charge.  Other have wireless charge.  Several options and more coming.  The Moto Z2 Play is out now, although only the Verizon locked version right now.  The website says the unlocked version is coming soon though.  This device is priced starting at $408 retail (not sure about the unlocked price) which is well below the premium phones with often cost over $700.  It has a Snapdragon 626 clocked at 2.2 GHz.  It has Quick Charge 3.0.  There is a version with 4GB of ram which is the one I would recommend but they don't have it available yet and I have not seen the price for that version.  The other Moto Z phones also look great but for most users, probably not worth the price point.  I would avoid the carrier locked versions myself.  The Moto Z Force Droid looks great except it is locked on Verizon and full of their bloatware.  It does have the shatterproof screen, a larger battery, and higher end specs which is great.

We bought one of these.  We got the Verizon only device with 32GB so it only has 3GB ram too.  We also got a battery mod with wireless charging.  Battery life even without the battery mod is excellent.  Adding the battery mod makes this a 2-day device with moderate to heavy use.  With the battery mod fitted, the device is a bit heavy.  I don't mind the weight but some may.

It has USB-C and Quick Charge 3.0 but it will not quick charge on Quick Charge 2.0 devices for some reason.  It quick charges fine on all my Quick Charge 3.0 devices including car chargers and battery backs.  On Quick Charge 2.0 devices it just charges regular.  There are good Quick Charge 3.0 accessories out there relatively cheap.

Update: We have 2 of these, one Verizon and the other unlocked.  The battery life is outstanding even without a mod battery.  Add even the smallest mod battery and 2 days of heavy use is no problem.

Moto X4

This device is not actually announced yet but the leaks are getting better all the time.  We expect this to be released this fall.  If the leaks are correct, this looks like a great upper-mid tier device.  

Google Pixel 2  

This is sure to have the cleanest Android experience you can get.  You will pay for it though.  This will be the second iteration of the new Pixel phone line and hopefully they fix some of the issues they had with the first. 

Update: This came out and it has the best camera on the market.  It also looks like they did make improvements in the right areas.  Great device but you do pay a steep price for it.

Saturday, March 18, 2017

Porsche Cayman Camera Mount

I bought a Garmin VIRB Ultra 30 action camera for recording in-car video in my 2006 Cayman S (987.1).  This camera uses the same mounts as GoPro cameras and many other action cameras. I found a good windshield suction mount that works great but sometimes its nice to get an in-car perspective.  I searched everywhere for a good mounting system.  I bought a clamp that I could use on the bar behind the seats, on the engine compartment.  However, the clamp was not rigid enough. It was also lower than I would like.
Camera clamp 

I kept searching for better options. I found one for over $400 and it still did not look great.  At this point I decided In would build one.  I went to the hardware store and bought about $35 worth of 3/4" aluminum square tubing, some 8mm all-thread, wingnuts, and washers.  I cut the tube into a 22" and 2, 5" lengths.  I removed the factory bar and installed the all-thread  into the bolt holes the original bar bolts were in.  Here is what I ended up with.




No special tools were needed.  Just a drill and saw.  It seems very rigid.  Road test coming soon.

I plan to just use this for track days and other events.  Its very simple and quick to swap the original bar back in as this camera bar is built for utility, not looks.

Here is a photo taken from the VIRB in the mount.




Saturday, December 31, 2016

Owning a Mercedes E350 4matic



We bought a used Mercedes Benz E350 4matic in September of 2015.  It is a 2010 (W212) model and it had 34k miles on it.  Our daughter is off to college which is over 500 miles to drive each way.  We have made this trip many times.  The car already has over 77k miles as of this post (December 2016).

The good

This car handles very well for a luxury sedan.  Of course I said the same about the Jaguar XJ8L we had before it.  Seems that luxury cars are no longer the bouncy boats they once were. This is a great car for long road trips.  As I mentioned above, we often take this on long trips and the driver fatigue is the lowest I have had in any car.  It's very stable and it inspires confidence while also being very comfortable. Once while driving through central Missouri a car quickly veered into me as I was passing.  I had to take immediate action to avoid a collision.  I had to steer quickly to the left, using all remaining pavement, possibly even dropping the edge of the left wheels off the pavement.  We were doing over 70mph.  I was easily able to control the vehicle with confidence and we avoided any damage.  

This car is very easy to enter/exit and to drive.  My wife has RA and she says it is a great car for her since everything about it is easy.  Doors open easy, it shifts easy, etc.  

I like the paddle shifts for the automatic trans.  In this car you need them too.  More on that below.

We like the look of the car, even in silver.  I generally prefer red or blue.  Silver and black are my least favorite car colors, and sadly the most popular on Mercedes.  I don't mind it so much on this car though.  

The entertainment system is very good.  I am shocked however that is does not support Bluetooth A2DP (music streaming).  That seems ridiculous for a 2010 model.  Especially when it supports everything else.  I do mean everything too.  It supports 6 DVD/CD, PCMCIA expansion, Satellite radio, AM/FM, weather radio, and it has a connector in the glove box where you can connect USB, video, and audio.  It has a built in hard drive that you can use to store music on as well.  The sound quality is great too.  

So far it has been easy to work on.  I have only done oil changes, spark plugs, and rear brakes but those were all very simple.  The engine compartment opens up to expose the whole engine which is rare these days.  So many cars have the engine tucked under the bodywork making it hard to access the rear of the engine.  Not this car.  Here is a photo with the air cleaner removed.
Engine bay with air cleaner removed
Removing the air cleaner is a few clips and hoses, no tools needed.  You can see all the ignition coils in plain sight here.  Another great feature is that I can reset the maintenance reminders myself with no tools.  It is done with the display and steering wheel buttons.  It is a bit tricky and takes me several attempts each time but at least I can do it which is more than I can say for Volvo and Porsche.

The 270HP engine makes decent power.  This is the lowest power gas engine for this model year.  Still, it's not too bad.  The powerband is broad too for a naturally aspirated engine.  Fuel economy is OK for an AWD luxury car.  I get mid-20's on a road trip and about 20 in town.  

Tire life has been very good.  

The not so good

While the seats are very comfortable, I don't like the fake leather they use to make them.  It is much hotter in the summer than real leather.  It also has a bad feel on the skin when wearing shorts.  Much better when you have some jeans to separate you from this material.  It seems very durable and it looks good but it feels bad on your skin.  I find myself missing that fantastic Jaguar leather.

Like most newer cars, the automatic transmission favors the highest possible gear and the convertor locked.  I think the convertor locks as soon as you are moving.  This is all done for fuel economy.  The downside comes when you are merging onto the freeway.  You his a steady speed in the cloverleaf when it is constant radius.  At this point it shifts into the highest gear.  As the ramp straightens out to merge onto the freeway, the car resists downshifting.  You keep going deeper into the throttle with little response until finally it drops about 3 gears and you accelerate away.  Like I said, this is typical of modern cars.  Here is where the paddle shifts come in.  I limit the upshifts to keep the engine above 2,000rpm or so.  I can now accelerate on smoothly.  You can optimize the gear using the paddles until you get to cruising speed.  Then you just hold the upshift paddle until D is selected.   One other issue with this trans happens when going up a steep hill at low speeds.  Again the trans will hold the highest gear with the convertor locked to the bitter end.  When it does finally downshift, it can occasionally be harsh.  

Like most cars this size it is cramped for 5.  You can ride 4 with decent comfort but that 5th person in the middle is a tight squeeze.  This is not just an E-class issue of course.  You need a pretty wide car to fit 3 adults across in comfort.  It's fine across town but after an hour on the road, the back seat occupants will complain.

Overall

This car has turned my wife into a Mercedes fan.  It is very likely her next car will be a Mercedes.  She wants to consider an S-class next time for the extra room though.  I like the car too.  I would probably get the E-class again as a like the less big size.  Now they have the E400 which is basically this car with twin turbos.  

Saturday, January 9, 2016

Mercedes E350 DTC's

I have a 2010 Mercedes E350 4-matic.  At about 38,000 miles the "check engine" light came on intermittently.  I scanned it with a generic OBD scan tool and the Torque app.  It returned P0496 and P1077.  It started out setting these DTC's only once in a while, about 1,000 miles apart or more but it eventually happened more often.  I subscribed to the factory documentation and searched for the Mercedes DTC definitions but the documentation did  not show these 2 DTC's at all.  The generic definition is canister purge flow high.  I inspected the related hoses and found nothing wrong.  I searched forums and found some comments that people had fixed this with a new purge solenoid.  I removed and inspected my purge solenoid and found nothing wrong.  I checked to make sure it moved freely and sealed properly.  I noticed an adjustment on the top of the solenoid that was covered with silicone sealer.  I was able to poke the correct size allen wrench into the adjustment and adjust it.  The adjustment changed how far the valve opened when energized.  I ran the screw in a turn or 2.  I made sure the purge valve would still open but at a lower flow rate.  After driving the car for a while to let the monitors run the check engine light returned but this time 2 different codes were set: P0455 and P1085.  Neither of these were covered in the Mercedes documentation either so I checked the generic definition.  Now it said gross evaporative leak.  Interesting.  The DTC's changed so I know I was on the right track.  I turned the adjustment about 1/4 turn out (CCW) and drove the car again.  The MIL went out (so far).

Missing DTC's in the service information is a big industry problem.  I had this same issue on my Jaguar XJ8L.  What often happens is the controls are flashed with newer software which changes the DTC's but the documentation does not get updated.

It is also lame that Mercedes has 2 DTC's trip at the same time for a single detected issue.

I finally fixed the issue with a new gas cap.

Sunday, July 26, 2015

Why I love Jaguar cars


Historically I was always a Ford fan.  I had all Fords until I acquired a BMW many years ago. My wife had always loved Jaguar cars.  They were beautiful, however, in the 1980's they were one of them most unreliable cars on the road.  British Layland pretty much destroyed the brand during this period and even today many people love the looks of the car but still remember the Jaguars of those years.

In 1989 Ford purchased Jaguar and began resurrecting it.  This took a long time as Jaguar was in bad shape at the time.  I bought my first Jaguar in 2000.  It was a 1994 XJ12.  We had a Ford Crown Victoria at the time and it had over 250k miles on it.  It was time to upgrade.  We looked at replacing it with another Crown Vic but when we saw the XJ12 for sale nearby we thought, what the heck.  We always wanted a Jag so now is the time.  I got the car cheap.  It was under $14k for a car that was originally over $70k.
This was not only my first Jaguar, but also my first (and only) V12 car.  This V12 had been upgraded under Ford ownership to fix all the oil leaks and other issues that had tarnished Jaguar.  We took this car on many trips and really liked it.  We eventually sold the car with 145k miles on it.

For a while I owned both the XJ12 and a 1998 XJR.  The XJR was a fantastic car for its day.  Very quick and fast.  Compared to the XJ12, and most other cars actually, it drove like a sports car.  I seriously considered taking this car to the track.
I still love the look of that XJR.  We sold this car with over 150k on it.

While the XJR was great in my book, my wife preferred a larger car with a smoother ride.  The XJR had firm suspension and wide tires for great handling.  She never used these features though.  So we bought a 2007 XJ8L.

In 2004 Jaguar created the X350 body style of the XJ which was all aluminum.  This reduced the cars weight considerably.  The whole car was redesigned and improved.  It was also larger.  The XJ8L is the long wheelbase version so it is even larger.  The back seat has enormous legroom.  It also has air ride suspension with active shocks.  Our 2007 was the last of the X350 (2008 was a slightly altered X351).

I also bought an X-Type.
The X-Type is really based on a Ford Mondeo. Being a Ford guy I am certainly good with that.  I will say though it is not like the XJ except in looks.  It rides like a Mondeo.  The X-Type and S-Type had heavy Ford influence and parts.  The XJ, XK, and the newer cars have very little in common with Ford.  Jaguar has always made their own V8 engines.  The new Jaguars now don't have any Ford parts.

So, why to we love these cars.  It is actually hard to explain to people.  Each time we were ready to replace our Jaguar, we drove many other cars and always came back to Jaguar.  They have a particular feel that is hard to describe.  The controls  are simple and intuitive.  The ride is really fantastic.  Not the boaty ride of years ago.  Firm yet compliant.  The car does not lean in corners yet it can soften up our nasty Illinois roads.  Acceleration is very good and smooth.  The XJR and XJ8L have a very pleasing exhaust note yet no drone.  People are amazed to hear the fuel economy this 2007 XJ8L gets.  I have done as good as 32 on the highway.  I always get 27 - 32 on the highway, and about 20-22 in town.  For a car this huge I feel very good about that.  The car just glides down the highway, even on terrible roads.  It is very controlled even at high speeds and the driver feels confident going fast.  The occupants are in a serene environment even when it is not so serene outside.

Jaguar has actually won or scored very well in several JD power's awards more recently. Both the quality awards and the APEAL awards.

I do all my own work on all my cars.  Jaguars are not that hard to work on.  


Saturday, July 18, 2015

Why I Love Porsche

I was raised in a Ford family actually.  Growing up our family owned all For and Lincoln vehicles and I really liked them.  The vehicle I drove most after getting my license was a 1972 Ford Bronco.  My first car was a 1968 Ford Mustang and I worked for almost 15 years at a Ford dealer.  However, a few years after high school I began to notice Porsche.  Reading car magazine around this time there was always a Porsche doing something great.  I liked the 911 because it was so different from other cars.  The rear engine design has many advantages for making a car fast.
  • The weight is already over the drive wheels for excellent traction
  • The drive wheels are the rear wheels where it belongs for best acceleration
  • On hard acceleration even more weight transfers to the drive wheels
  • The flat engine design keeps the weight very low in the chassis for better handling
  • The engine being so close to the rear axle helps reduce the moment of inertia when the car changes directions (turns)
  • The car was simple and light.
I guess I was a closet Porsche fan from that point on.  It was not until 2004 that I would actually buy a Porsche, and it was not a 911.  Unfortunately Porsche's are rather expensive.  In my case, my first Porsche was replacing my 3rd car and it is a bit harder to justify a 3rd vehicle.  We had only 2 cars until 2000 when my in-laws gave us their 1984 BMW 318i so I was replacing a car I had acquired for free.  My budget at the time did not have room for a 911.  I found a 1987 944S locally so I drove it.  After a short drive I decided it belonged in my garage.  I owned that car for 10 years.  

Not long after I bought the 944S I joined the Porsche Club of America.  There was a fairly active local region, and the president of that region worked in the building next to where I worked.  We got to know each other.  One day I was complaining that their website was out of date so he appointed me webmaster.  Next thing you know I am on the board of the local region.  

I joined the PCA mostly to attend track days, also known as drivers education or DE.  I had heard about them and really wanted to go.  In high school, and for several years after, I would drag race occasionally at a small 1/4 mile track near my home in Washington State.  Drag racing is fun but you only get a few seconds of fun at a time.  I was ready for a road course.  My first DE was at Blackhawk Farms.  I was a Chicago Region PCA event for novices such as myself.  I had a blast and was hooked.  I attended a couple events a year for several years there at tracks within a few hours drive. 

In 2014 I bought a 2006 Cayman S.  That story is here.  My first track day in that car was a Putnam Park, my favorite track.  Every car brand has a unique feel.  Its hard to describe the feel of each brand, you just have to drive them.  Most people tend to get used to the feel of the brand they drive so other brands feel different.  I think this is much of what creates brand loyalty.  Porches definitely have a special feel to them.  Even the 944S had a special feel, even though it was a front engine inline 4 cylinder car.  The Boxster, Cayman, and 911 are very different than other cars though.  The car is so different than most other cars and you feel it as soon as you push the car.  Typical cars seem to complain when driven hard.  Tires squeal, the car leans and groans in corners, and the engine wheezes under full throttle.  Not the case in a Porsche.  They love it.  The harder you push them, the happier they are.  The engine sings to you as you approach red line at wide open throttle.  It sounds so good that I often hit the rev limiter before shifting.

As I mentioned above, the Boxster, Cayman, and 911 have a very unique layout which has many advantages.  The 911 is the most unique having the engine actually behind the rear axle.  The Boxster and Cayman are mid-engine which is a layout shared with nearly all supercars. The unique thing about the Boxster and Cayman is that they are not only mid-engine, but they use a flat 6 engine in the middle.  Most supercars are a V engine (V6, V8, V12, V16).  The flat engine is much better for weight distribution because it keeps its weight very low in the chassis.

Now the engine weight is not only in the middle of the car, towards the rear where the drive wheels are, but it is also down very low.  This makes it the best handling car you can get really.  It also make for fantastic stopping as the rear wheels are actually providing much of the stopping power unlike front engine cars.  When you look at the layout and features of the Boxster and Cayman, these cars are a bargain even at the fairly high prices they command.  There are not many low priced mid-engine performance cars out there.  If you go back a bit you could say things like the Pontiac Fiero and Toyota MR2 were also mid-engine and were cheaper.  This is true, but they were also cheaper in every way, not just less expensive.  The  modern Lotus cars are probably the closest and they are priced similar.  

Porsche cars are really made for track duty.  You can take any Porsche right from the showroom to a DE, have fun all weekend, and drive it home.  This is not true with most cars.  Usually the brakes just can't handle the repeated heavy braking of a track day.  They will fade or worse, boil the fluid and fail.  Most performance cars can handle it OK if you upgrade the brake pads and fluid.  I ran street pads at Putnam in the Cayman with no fade at all.  

While some may consider Porsche an exotic, they can really be driven daily too.  I would not put Porsche in the same group as Ferrari or Lamborghini for instance.  They cost far less to own and maintain than those cars.  They are also much more reliable.  Porsche has many JD Power quality and APEAL awards.  You often see Porsche's with well over 100k miles on them.  It is rare to find a Ferrari or Lamborghini with high miles.  I drive my Porsche to work every day when there is no salt on the road.  I used it for grocery shopping, runs to the hardware store, etc.  It is my daily driver.  Porsche does make real exotics though.  The 959, the Carerra GT, and the 918 for instance.  These cars often outperform those other exotics.  The 918 still has the track record at the Nurburgring Nordschleife.

While these cars are a joy to drive everywhere, you can't fully enjoy a Porsche just driving it on public roads.  You really need to spend some time driving one at speed on a real track.  Only then can you fully experience the difference.  

Everything in life is a trade-off decision. For many a car is simply a transportation appliance meant to move people and things from place to place.  They look at a car much like I look at a washing machine.  You find one that will do the job for as cheap as you can while maintaining reliability.  Many such as myself however, view cars much differently.  They are a thing of both visual and audible beauty.  They excite your senses.  The driver and car combine to make an athlete.  Those shopping for a transportation appliance generally look at these priorities.
  • Miles per gallon
  • Cupholders
  • Utility
  • Seating capacity
  • Reliability
  • Purchase cost
  • Smooth ride
I have these priorities.
  • Smiles per gallon
  • Power and acceleration
  • Handling
  • Braking
  • Lap times
  • Aesthetics
  • Feel and sound

I do not consider myself a badge snob.  I would be more than happy if everyone could own a Porsche.  Exclusivity is not something I am into at all.  Sadly some do buy Porsche for this reason alone and it tarnishes the brand a bit in my opinion.  People get the wrong impression of Porsche owners.  

Thursday, June 4, 2015

How to start using a new Android device and get the best experience from it

There are many Android devices out there today.  This article will focus on tablets and phones.  Android is an operating system, similar to Windows or Linux.  However, Android does allow a significant amount of customization by the manufacturer who are creating an Android build for a device the sell.  Unfortunately device manufacturers can't seem to leave a good thing alone.  They put what is called "skins" on Android that make it look and act very differently.  Some of these include:

  • Amazon Fire OS
  • HTC Sense
  • Samsung Touch Wiz

For the most part, these modified Android versions are much worse than the proper Android which leads to a poor user experience, crashing, delayed updates to new operating systems, and inconsistency between devices.  I have been an Android user since the very first Motorola Droid came out in 2009.  I also had one of the first official Android tablets the Motorola Xoom.  When I try to use a Samsung or LG device, I have a hard time finding things.  The settings are all different.  Too much just looks and works differently.  As an app developer, I have also run into many issues caused by the customs versions of Android.

In addition to the custom operating system, they also create their own custom apps for email, calendar, phone dialer, contacts, file backup, device backup, etc.  None of these work nearly as well as the Google apps.  In the case of devices branded and sold through a cellular provider (the vast majority) it gets even worse.  Far worse.  Now the cellular provider really pollutes the device with a bunch of really awful software like their own versions of device backup, app stores, file storage, etc.  This adds yet another layer of terrible software on top of terrible software that really hurts the user experience and makes updates drag on for eternity, if ever.

So, how do we make things better.

  1. When you first get your new device make sure you log into it with your Gmail account that you create, preferably ahead of time.  Do not log into the cellular provider backup or file storage accounts.  Skip those steps.  Do not have the cellular store try to copy your contact in either.  They generally make a mess of it.  Their generic contact converters seem to always mess up copying fields from your current contacts.  If you have a non-smart phone you can use BitPIM to extract your old contacts.  Then upload them to Gmail using a PC and clean up any issues.  Use the PC to add new contacts as well.  Once you have your Gmail contacts correct, they can sync to the phone.  You can then manage them on the phone or the PC.
  2. If your phone or tablet has a confusing home screen and interface, install Google Now Launcher right away.  I recently bought a Lenovo tablet and the first thing I noticed was the terrible home screen.  Installing Google Now Launcher made a huge difference.  
  3. Disable and uninstall all the bloatware and terrible device manufacturer and cellular provider software that you don't want or is redundant with the Google apps like mail, calendar, backup, etc.   You do this by going to Android settings, finding "apps" in the list and selecting it.  This should list apps on the device.  Be careful to ensure you are seeing all apps, not just the ones you added.  You do this by scrolling to the right.  You will see the tabs change from "downloaded" to "running", to "all".  Make sure it is in then "all" tab.  Scroll down to the apps you don't want and select them one at a time.  For each app, click the "uninstall" button if it is available.  If "uninstall" is not available but "disable" is then disable.  
  4. Now install the right apps.  I prefer all the Google apps for most things.  
    1. Google Calendar
    2. Google Maps
    3. Google Drive and the related Docs and Sheets 
    4. Google Photos
    5. Gmail or Google Inbox
    6. Google Hangouts
    7. Google Translate
    8. Google Play Music
    9. Google Play Newsstand
    10. Google Play Movies & TV
    11. Google Play Books
    12. Google text-to-speech
    13. Google Camera
  5. Now disconnect all the older bloatware apps and connect the Google apps instead.  Start with calendar.  The other calendars are mostly junk as you store much of your calendar locally and they often don't connect or sync correctly with Google calendar.  Open Google Calendar and make sure you are logged in and that the local calendar is not the default calendar.  Use your google calendar for all appointments.  This way everything in synchronized in the cloud and you can manage it both with a PC and the phone.  You can also easily connect to other calendars such as school, clubs, etc.
Another option of course is to just buy a Nexus device to begin with and all of this is already taken care of for you.  I prefer Motorola devices.  The newer (Google ownership and after) are much cleaner than most so it is as close to a Nexus you can get short of a Nexus.  Now you can get the Nexus 6 which is both Nexus and Motorola.  Motorola finally started bypassing the carries all together.  Now you can get the 2015 and up Moto-X and other models direct from Motorola, unlocked, and bloatware free.

One other issue with the user experience is push notifications.  I guess this is a personal thing but there are very few push notifications I want.  Nice thing about Android is you can block apps from pushing notifications to your notification bar, beyond just the settings in the app itself.  There are several apps I do block because they misuse it.  In order to block an app from notifying, go to settings, then apps, then select the app of interest.  This is the same place we were above to disable and uninstall.  This time though just un-check  "show notifications".  That app can no longer put stuff on the notification bar.  Great feature.  

I actually don't have Facebook app installed.  Facebook is the kind of app that abuses push notifications and it has other issues.  I do use Facebook however.  I just have a shortcut on my home page that is a bookmark to the website.  Most people cant even tell the difference.  My home screen button looks the same as the app.  When you click the shortcut the website loads a mobile optimized page that looks nearly identical to the app.  The beauty of this is that Facebook cannot run in the background chewing up battery and data, and it can't pester you. Chrome browser added the ability to do push notifications in web apps in 2015.  However, when you first load the page the web app will ask if you want push notifications.  You can say no here.  To add a web app to your home screen in Chrome (on Android or desktop) use the menu and click the "add to homescreen".

Believe it or not Microsoft of all companies have made some good Android apps and services lately.  Some of these may rival Google.  In some cases I have both.  I use both Google Drive and One Drive for instance.

I started using Waze for navigation.  It has a fantastic crowd sourced traffic data that is unrivaled.  It is also owned by Google by the way.

The new Google Photos includes free backup of all your photos (up to 16MP) and videos (up to 1080p).  That is the best deal out there.  They also have a PC app to back up everything from your PC too.  You do have the option to backup larger photos and videos but that will cost Drive space.  16MP and 1080p is very good size, and happens to be equal or larger than most phones will shoot anyway.

I use Hangouts for SMS, MMS, and Hangouts IM, voice calls, and video calls.  It works great and free all over the world (except China where nothing Google works).  When I travel in and outside the US I can connect WiFi at my hotel and call home for free.  Very nice.  I have all my messaging in one place too.  Skype will do about the same except for SMS/MMS so it is another good option.

I like both Google Play Newsstand and Google News & Weather.  I read the news on both these apps every day.  With Newsstand, you can even connect to subscribed papers and magazines.  I subscribe to the Wall Street Journal via Newsstand for instance.

Google Play Music is also a great app.  It lets me use my music library both in the cloud and on the device to create instant mixes.  This is great for long trips where you don't want all kinds of strange music you don't like from a Pandora or the like since you can have Google Music use only your music for the mix.  It also has ad free streaming if you want it.

I use My Tracks to track my bicycle rides.  The only issue I have with it is the calorie estimator.  So, I also use Cardio Trainer.  I run both apps at the same time on the same device.   The only issue is you can only connect your heart monitor to one of them at a time.